Do not ignore the forklift at the workplace. If the operation is not good, there will be major mishaps in minutes, and there are lots of mishaps including forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving crash.
Situation 2: In order to preserve the equilibrium of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The width of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is squashed when the forklift surrender.
Situation 7: The forklift driver did not put on a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles nearby, the driving signal must be released first. High-speed doglegs are prohibited. High-speed sharp turns will certainly create the car to lose side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the factory and must keep a specific security distance from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable placement that does not hinder the driving, and the gantry must be appropriately slanted back. The tons will not be increased except when stacking or loading. .
8. The height of the load must not block the driver's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt way, and they will never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the lots is lowered to enable very easy placement of the load and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to lift personnel to participate in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to make use of the brake inertia to slip, put, round or roll objects. .
10. It is not allowed to utilize forks to choose, transform pallet discharge.

Leaving .
1. Electric Forklift Truck for Warehouse It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump Stand-on Electric Pallet Stacker the goods or reduced the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be checked, and fuel, lubing oil and air conditioning water need to be included.
2. Inspect the security efficiency of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the exterior leak ought to also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the auto;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo must be 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be too sharp to stop the propensity of " totally free switching";.
6. Running up and down the incline must be slow and consistent, and no turning on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or hefty goods and go to the driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844